Printable View
What the best way to pull this multiple mob when trying to move them away while keeping maximum Threat on them?
I try Shield lob mob 1, flash, Voke mob 2 shield lob, flash, scorn, then when I move them to the corner but they still go everywhere sometime when DPS blast the crap out of them. Getting a hard time getting them to a corner first.
Is Shield lob and do Rage of Halone without combo better keeping Threat?
Hit Titan when he lands with a Fast -> Savage. Wait for adds to spawn. Hit one add with the combo'd Halone, shield lob the other (twice if necesarry). Spam Flash. Then start normal threat rotation.
Works for me.
I use the warrior version with a butcher's block waiting. Chopped one add, tomahawk the other and over power to draw them near. Then infuriate plus steel cyclone. Remember to dodge their mini landslide!
I saved combo'd Halone+SW on west add, then run toward east add and do shield lob+non combo halone. Just flash and CoS after that.
When Titan land down from jump:
- Cast 1 stone skin (use spare time)
- Fast Blade
- Savage
- Keep combo for Halone
- Titan cast adds, run to let side
- Left Egi, land Halone
- Run to right and throw shield lob twice to 2nd adds.
- Spam Flash until 1/2 mana
- Cast Sentinel + Tempered Will , to reduce healer work and chance of getting landslide.
- Spam Flash and cast Stone skin.
For Adds round 2, change from Sentinel + Tempered Will to Hallowed Ground.
Sometime i will provoke 2nd adds instead of shield lobx2. Usually the time need to kill 2 adds will be almost the same as cool down of provoke and same time as MT getting 3rd stack before Upveal move.
I tank it as a warrior but I do something similar. I actually go Heavy Swing on titan, move to the left and wait for the egis to spawn. I hit the left egi with Skull Sunder and the move to the right and hit the right egi with Butcher's Block. I then use one steel cyclone and one overpower and I have agro for their entire hp pool. At that point I usually start dpsing whichever egi has higher hp (usually the left egi as MNK starts on the right one).
As a paladin I would go Fast Blade on Titan, Savage Blade on the left egi and Rage of Halone on the right egi. Then hit flash 3-4 times and start dpsing whichever add has the higher hp pool.
Alternatively (for WAR) once you have both together:
SC -> Infuriate -> SC
Then you can work on building your Wrath back up on the Egis so you have an IB ready for the tank swap after.
Admittedly I play WAR, but I dunno if flashing is very effecient beyond the blinding utility on two targets. You should be able to build up for a RoH just as they land, then FoF->RoH the target your single DPS will focus, followed by a Shield Lob on the other one to bring them together, Flash while getting them into position, then continue with Fast and Savage Blade on the target not focused, while switching over and finishing the combo with RoH on the other one. This should be enough to hold aggro, unless your DPS is much higher iLvl than you.
What I do as a WAR is just BB the left one, Tomahawk right one, bring them together and immediately Steel Cyclone, move into position while infuriating and doing another SC. This will guaranteed hold aggro untill they're down, so I can focus on Storm's Pathing my way up to 5 stacks to prepare for the tank switch.
Oh, and don't forget to pop a CD or two to ease up the healing, as either tank.
I have a Rage of Halone combined up, use it on the left add then run over, Spirits Within on right add then Flash, pop Sentinel and start doing combos and avoiding landslides.
Are you running through the Egis to avoid land slides or just side stepping?